Change or rekey · St. Agatha
Lock Replacement & Upgrade in St. Agatha
Three teenagers, a dog walker, a cleaner and one house key that keeps going missing.
In plain words
Lock replacement and upgrade is the service that takes tired or under-built door hardware off and puts hardware suited to the door in its place. It ranges from a like-for-like deadbolt on a back door to a complete refit of every entrance with heavier-grade locks, reinforced strikes and one key for the house. The locksmith first confirms that the person ordering the work has the right to change the lock, then examines the door, measures the existing preparation and recommends hardware that fits it cleanly. The visit ends with each lock tested from both sides, keys in your hand and the packaging and instructions left with you.
How the visit goesThree teenagers, a dog walker, a cleaner and one house key that keeps going missing. You are tired of cutting copies and would rather give each person a code you can switch off, with a proper deadbolt behind it.
Lock Replacement & Upgrade
How the visit goes
Exposure, weather and finish
The locksmith looks at where the door lives. A side entrance beside a salted driveway, a south-facing front door in full sun and a sheltered porch each treat a finish differently, and the residential hardware label scores finish durability as its own category for exactly this reason. Existing hardware is examined for pitting, peeling and green bloom, which shows how hard the spot is on metal. That guides the choice between a PVD brass, a satin nickel, a powder-coated black or a stainless product, and whether a storm door or a small hood would help. Matching the rest of the entrance comes last, once the finish will survive the location.
Fitting the latch or bolt to the door
Most modern latches and bolts adjust between the two common backsets, so the unit is set to the measured figure and slid into the edge bore. A spring latch goes in with its bevel facing the strike, while a deadbolt is oriented the way its markings or instructions call for, not by that bevel rule. The faceplate should sit flush in its mortise; where the old cut-out differs in shape or size, the mortise is trimmed with a sharp chisel, or a round drive-in collar is used where the door was prepared that way. The bolt is checked to travel freely before anything else goes on, since a bolt that binds in the door will bind under the key too.
A clear plan for the remaining doors
Most households do not replace every lock in one visit, and you leave with a short list of what is left, in order of importance. Typically the front door and the garage-to-house door come first, then the back and side doors, then the patio slider and interior sets. Because the key plan has been settled, any lock added later can be pinned to the same key, so the house stays on one key as the work continues. Finishes and styles are recorded so future hardware matches. The first visit sets the standard; the rest of the house can follow when it suits you.
Lock Replacement & Upgrade
In the van
Manufacturer-approved cylinder lubricant
Adjustable latch or bolt
75 millimetre strike and hinge screws
Graded deadbolt
Boring jig and hole saws
Lock Replacement & Upgrade
What affects the quote
Number of doors
One back door is a small visit; the front, back, side, garage man-door and patio slider together are a longer one, though several doors done at once share the travel and setup.
Authorization needed from a property manager or landlord
A rental or condominium unit sometimes needs sign-off from a property manager or landlord before a lock is changed, and new keys may need to reach more than one party afterward. Confirming who is authorized and who receives keys is worked out before the new hardware goes in.
Keys cut
Each key is counted, and restricted keys cut against a card are a different item from standard blanks. Say how many people need one and the quote lists them.
What to have ready
- Do you own the home, or rent it with the landlord's agreement to change locks?
- Which finish should the new hardware match?
- Are you interested in a keypad or smart lock on any door?
Lock Replacement & Upgrade: questions
QuestionsWill a new lock fit the holes already in my door?
Usually, yes. Most residential doors are prepared to standard sizes, a 54 millimetre cross bore and a backset of 60 or 70 millimetres, and most modern hardware adjusts between those backsets. The locksmith measures before choosing, so the new lock is matched to the door rather than the other way around. Where an older mortise lock or an unusual bore is found, filler plates, extension kits or a carefully jigged new bore bring the door to standard.
Is there anything different about steel or fibreglass doors?
The lock hardware is the same; the door construction changes the method. Steel and fibreglass doors have a wooden or composite block inside the lock stile, and existing bores are used wherever possible. Where a new deadbolt must be added, the locksmith drills with a jig and bits suited to the skin so the hole is clean and square, and fits an edge plate designed for that door. Insulated doors also move less with humidity, so alignment tends to hold well.
What information helps before the visit?
Photographs of each lock from outside and inside, plus one of the door edge showing the latch plate and one of the strike on the frame, tell the locksmith most of what they need. Add the door thickness if you can measure it, whether the door is wood, steel or fibreglass, the finish you want to match, how many doors are involved and whether you want them all on one key.
Related services
- Deadbolt InstallationYou bought a keypad deadbolt online and pulled the old one off, only to find the hole in the door is a different size and the bolt latch sits at a backset the new kit does not list.
- Vintage Mortise Lock ServiceSomeone painted the door years ago without removing the hardware.
- Smart Lock InstallationYou have just taken possession of the house and the previous owners handed over a keypad deadbolt with a code nobody wrote down and an app account you cannot get into.