Car keys · Wilmot
Ignition Lock Repair in Wilmot
The key turned the engine off in the driveway and now refuses to come back out.
In plain words
A key that has snapped off inside the ignition barrel is not the end of the key, or of the barrel. The broken piece is drawn out with hooked or spiral tools built for the job, without pushing it further in, and the cylinder is checked afterward for the wear that likely caused the break in the first place. A fresh key is then cut and tested before the visit ends.
How the visit goesTurning the key used to take one smooth motion. Lately it grinds partway through, sometimes needing a second attempt, and yesterday it stopped reaching start altogether. The key itself looks the same as always; something inside the ignition has changed instead.
Ignition Lock Repair
How the visit goes
Reading the exact symptom
The next question is about behaviour, not diagnosis. Does the key insert at all? Does it turn partway, all the way, or not at all? Does it turn without the steering lock releasing, or without the dash lighting up? Is it stuck, unable to come back out once the engine is off? Each answer points somewhere different inside the mechanism, and a locksmith who hears the exact sequence before arriving brings the right decoders, extraction tools and replacement parts rather than guessing from a general description that the key just does not work.
Testing every position before calling it finished
A repaired or replaced cylinder is cycled through every stop, off, accessory, on and start, with the key the owner will actually use afterward. The steering lock is engaged and released several times, the dash is watched for the expected response at each position, and the engine is started and shut off to confirm the whole sequence holds up in practice rather than just on the workbench.
Knowing exactly what was done
You are told plainly whether the cylinder was serviced, repinned or replaced, whether anything else near the column was removed and refitted, and whether a broken key fragment came out along the way. Any part that was swapped is handed to you or set aside as you prefer, so nothing about the visit stays a mystery once the locksmith has packed up and left the driveway.
Ignition Lock Repair
In the van
Broken key extractors
Retaining pins and clips
Key code reader
Keyed-alike pinning kit
Cylinder decoder
Ignition Lock Repair
What affects the quote
Keying other locks to match
Bringing the doors and trunk onto a newly pinned ignition key, so one key runs the whole vehicle again, is separate work from the ignition repair itself, even when it happens during the same visit.
Time needed to test every position
Cycling the ignition through every switch position and the steering lock, more than once, with the engine started and stopped to confirm the repair holds, adds a small amount of time on top of the repair.
Number of new keys cut
One replacement key is the simplest case. A household or a business vehicle used by several people may want a few keys cut and tested at once, and each one is counted into the visit.
What to have ready
- Is the key stuck and unable to be removed?
- Has this ignition been serviced or replaced before?
- Do you have the vehicle permit or proof of ownership handy?
Ignition Lock Repair: questions
QuestionsIs my vehicle's security system disabled while this work is happening?
No part of the vehicle's electronic security system is bypassed or defeated as part of a mechanical ignition repair. The locksmith works on the physical cylinder and its housing, and any question involving the immobilizer or transponder system is identified and referred rather than worked around, so the vehicle's built-in protection stays exactly as it was designed to work.
How many keys will I leave with?
That depends on what you ask for and what the vehicle already has. A single working key is enough to drive away, but most people ask for at least one spare cut and tested at the same time, especially if the visit started because the only working key had worn down badly or snapped off inside the ignition altogether.
What information should I have ready when I call?
The vehicle's year, make and model, and exactly what the key does: whether it inserts, turns, engages anything, or is stuck. Mention whether a spare key exists, whether anything has already been tried on the lock, and whether the vehicle's warning lights or dash behave normally otherwise. Having the vehicle permit or registration nearby helps the ownership check move along smoothly.
Related services
- Car Key ReplacementAfter fifteen years the blade has worn to a smooth sliver.
- Spare Car Key DuplicationA lockout last month ended with a locksmith opening the door and going home, and the same single key has been carried ever since with nothing behind it.
- Key Fob ProgrammingThe car changed hands last week, and the paperwork included exactly one fob for a household with two drivers.